ABB IRB 390 Скачать руководство пользователя

Страница: 52 / 346

3.3.5 Orienting, assembling and securing the manipulator

Overview of the assembly order

The IRB 390 is delivered in sub-assemblies which are assembled in the following
order:

Illustration

Assembly order

xx2000000683

Install the base unit.

Note

The distance washer (a) and
sealing (b) are packed separ-
ately in the delivery.

Move the upper arms into
synchronization position.

Attach the lower arms to the
upper arms.

Attach the delta unit to the
lower arms.

Attach the telescopic unit.

Calibrate the robot.

Detailed procedures for each step are given further on in this section.

Attachment screws

The table below specifies the type of securing screws and washers to be used for
securing the robot to the base foundation.

M16 stainless steel. Minimum length of
thread engagement: 24 mm

Suitable screws

3 pcs

Quantity

Minimum quality: A4-80

Quality

17x15x3 stainless steel (3HAC060866-005)

Suitable washer

Continues on next page

Product manual - IRB 390

3HAC066566-001 Revision: B

3 Installation and commissioning

3.3.5 Orienting, assembling and securing the manipulator

Содержание IRB 390



























































































































































































































































































































































Результаты поиска

Содержание IRB 390

Отзывы:

Похожие инструкции для IRB 390

Бренды по названию

Популярные бренды

ABB IRB 390, Руководство по эксплуатации продукта

Результаты поиска

Содержание IRB 390

Отзывы:

Похожие инструкции для IRB 390

Бренды по названию

Популярные бренды