manualshive.com logo in svg

ABB i-bus VC/S 4 1 Series, Руководство по эксплуатации продукта, Страница: 73 / 199

Поделиться
Скачать
ABB i-bus VC/S 4 1 Series Скачать руководство пользователя страница 73

ABB i-bus® KNX 

PARAMETERS

7.4.31

Operating mode after exceeding monitoring time

This parameter is used to define which operating mode is activated if no value is received on group ob-
ject 

Operating mode normal (master)

 during the specified period. This operating mode remains active

until a new value is received on group object 

Operating mode normal (master)

.

Option

Building Protection

Comfort

Standby

Economy

Prerequisites for visibility

• Parameter window 

Channel X

 \ Parameter window 

Application parameters

 \ Parameter 

Channel

function

 \ Option 

Controller channel

• Parameter window 

Channel X

 \ Parameter window 

Monitoring and safety

– Parameter 

Cyclical monitoring

 \ 

Option 

Activated

– Parameter 

Monitor receipt of group object "Operating mode normal (master)"

 \ 

Option 

Activated

• The parameter is in the parameter window 

Channel X

 \ parameter window 

Monitoring and safety

.

7.4.32

Operating mode after bus voltage recovery or ETS download

This parameter is used to define which operating mode is activated after bus voltage recovery or ETS
download. The operating mode remains active until a new operating mode is set.

Note

After an ETS reset the 

Comfort

 operating mode is always set.

Note

The operating mode should be defined during the planning phase. If the operating mode is defined in-
correctly, this might reduce comfort or increase energy consumption.

For an explanation of the individual operating modes → ⁠

Explanation of the operating modes, Page ⁠⁠174

.

Option

Comfort

Standby

Economy

Building Protection

As before bus voltage failure/download

Prerequisites for visibility

• Parameter window 

Channel X

 \ Parameter window 

Application parameters

 \ Parameter 

Channel

function

 \ Option 

Controller channel

• The parameter is in the parameter window 

Channel X

 \ parameter window 

Setpoint manager

.

Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B  

73

Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page

Содержание i-bus VC/S 4 1 Series








































































































































































































Отзывы:

Нет отзывов