ABB i-bus VC/S 4 1 Series, Руководство по эксплуатации продукта, Страница: 165 / 199

ABB i-bus® KNX GROUP OBJECTS
Function Group object name Data point
type Length Flags
Request setpoint adjustment (master) Channel X – Controller DPT 6.010 1 byte C W
This group object is used to receive a setpoint adjustment via the bus (ABB i-bus® KNX).
The setpoint adjustment must lie withing the permitted setpoint range; see following parameters:
•
Max. manual increase in heating mode via KNX
•
Max. manual reduction in heating mode via KNX
• Max. manual increase in cooling mode via KNX
•
Max. manual reduction in cooling mode via KNX
If the required temperature is outside the permitted setpoint range, the maximum/minimum possible value is set. The master device checks the value received and
returns the set value via group object Confirm setpoint adjustment (master) [DPT 6.010].
The data point type of the group object depends on the setting in the parameter
Data point type, manual setpoint adjustment .
Telegram value:
•
-128 … 127
Note
If a slave is used:
This group object must be connected to the corresponding group object of the slave to ensure the functionality of master/slave operation.
Prerequisites for visibility
• Parameter window Channel X \ Parameter window Application parameters \ Parameter Channel function \ Option Controller channel
• Parameter window
Channel X
\ Parameter window
Setpoint adjustment
– Parameter Connect analog room control unit to physical device input a \ Option No
– Parameter
Data point type, manual setpoint adjustment
\ Option
DPT 6.010 (meter pulses)
Confirm setpoint adjustment (master) Channel X – Controller DPT 9.001 2 bytes C R T
This group object sends the confirmation of the setpoint adjustment on the bus (ABB i-bus® KNX) as was requested via group object Request setpoint adjustment
(master) [DPT 9.001].
The data point type of the group object depends on the setting in the parameter
Data point type, manual setpoint adjustment .
Telegram value:
•
10 … 40 °C
Note
If a slave is used:
This group object must be connected to the corresponding group object of the slave to ensure the functionality of master/slave operation.
Prerequisites for visibility
• Parameter window Channel X \ Parameter window Application parameters \ Parameter Channel function \ Option Controller channel
• Parameter window
Channel X
\ Parameter window
Setpoint adjustment
– Parameter Connect analog room control unit to physical device input a \ Option No
– Parameter
Data point type, manual setpoint adjustment
\ Option
DPT 9.001 (absolute temperature value)
Confirm setpoint adjustment (master) Channel X – Controller DPT 6.010 1 byte C R T
This group object sends the confirmation of the setpoint adjustment on the bus (ABB i-bus® KNX) as was requested via group object Request setpoint adjustment
(master) [DPT 6.010].
The data point type of the group object depends on the setting in the parameter
Data point type, manual setpoint adjustment .
Telegram value:
•
-128 … 127
Note
If a slave is used:
This group object must be connected to the corresponding group object of the slave to ensure the functionality of master/slave operation.
Prerequisites for visibility
• Parameter window Channel X \ Parameter window Application parameters \ Parameter Channel function \ Option Controller channel
• Parameter window
Channel X
\ Parameter window
Setpoint adjustment
– Parameter Connect analog room control unit to physical device input a \ Option No
– Parameter
Data point type, manual setpoint adjustment
\ Option
DPT 6.010 (meter pulses)
Request heating/cooling (master) Channel X – Controller DPT 1.100 1 bit C W
This group object is used to receive the heating/cooling status via the bus (ABB i-bus® KNX) and to synchronize the controller (master) with the slave.
Telegram value:
•
1 = Heating
• 0 = Cooling
Note
If a slave is used:
This group object must be connected to the corresponding group object of the slave to ensure the functionality of master/slave operation.
Prerequisites for visibility
• Parameter window Channel X \ Parameter window Application parameters
– Parameter Channel function \ Option Controller channel
– Parameter Basic-stage heating [controller] \ all options except Deactivated
– Parameter Basic-stage cooling [controller] \ all options except Deactivated
– Parameter Heating/cooling changeover \ Option Via group object or via slave
Status Controller RHCC Channel X – Controller DPT 22.101 2 bytes C R T
This group object sends the following items of status information (according to the specification for the RHCC status) on the bus (ABB i-bus® KNX):
•
Operating mode Heating / cooling
• Operation active / inactive
• Status Building Protection
• Fault (failure of actual-temperature measurement)
Prerequisites for visibility
• Parameter window
Channel X
\ Parameter window
Application parameters
\ Parameter
Channel function
\ Option
Controller channel
Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B 165
Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page