ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 67

Страница: 67 / 152

ABB i-bus

KNX

Commissioning

JRA/S 6.230.3.1 | 2CDC506083D0201 65

3.3.3.1

a: Blind sensor parameter window

This operation mode allows the operation of blinds and shutters with buttons or switches.

This parameter window is visible if the

Blind sensor

option is selected in the Input a Function parameter

window, p. 64.

Enable group object
"Block" 1-bit

Options:

No
Yes

•

Yes:

The 1-bit group object

Block

is enabled. This can be used to disable the input.

Note

If the input is disabled and the option

Send cyclically

is set, the last state is still sent regardless of the

block. The

Block

option still blocks the physical input; sending continues internally.

Debounce time

Options:

10/20/30/50/70/100/150 ms

Debouncing prevents unwanted multiple operations of the input, e.g. due to bouncing of the contact.

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Результаты поиска

Содержание i-bus KNX JRA/S 6.230.3.1

Отзывы:

Бренды по названию

Популярные бренды

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Результаты поиска

Содержание i-bus KNX JRA/S 6.230.3.1

Отзывы:

Бренды по названию

Популярные бренды