manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 111

ABB i-bus

®

 KNX 

Commissioning 
 
 

JRA/S 6.230.3.1 | 2CDC506083D0201   109 

3.4.5 

Output A,B: Blind and Shutter group objects 

This section explains the Output A,B: Blind and Shutter group objects using the Blind option. If the blind 
option has a special function or if the function is not available, e.g. slat adjustment, this is clearly indicated. 
Otherwise, the explanations apply for both operation modes.  

No. 

Function 

Object name 

Data type 

Flags 

75 

Move UP/DOWN 

Blind Output A,B  

Shutter Output A,B  

1 bit 

DPT 1.008 

C, W 

This group object is enabled if the 

Mode Output

 parameter is set to 

Blind

 in the 

Output A,B: Mode

 parameter window. 

If this group object receives a telegram with the value 0, the blind moves UP. If it receives a telegram with the value 1, it 
moves DOWN. The output contact returns to the neutral middle position after the 

Total travel time

 has elapsed. 

Telegram value 

0 = UP 
1 = DOWN 

 

76 

STOP/Slat adj. OPEN/CLOSE and/or 

STOP UP/DOWN 

Blind Output A,B  

Shutter Output A,B  

1 bit 

DPT 1.007 

C, W 

This group object is enabled if the 

Mode Output

 parameter is set to 

Blind

 in the 

Output A,B: Mode

 parameter window. 

This group object stops the shutter or blind during movement. When the shutter is stopped, the group object is used for slat 
adjustment, one step UP (0) or DOWN (1).  

If the blind is moving, the movement stops if a telegram is received on this group object, regardless of whether a 0 or a 1 is 
received. 

Blind

 mode: If the blind is at a standstill when this group object receives a telegram the blind is moved UP (0) or DOWN (1) for 

the duration of slat adjustment and then stops. 

Shutter

 mode: If the shutter is at a standstill when this group object receives a telegram, no action is undertaken. 

Telegram value 

0 = STOP/slat adjustment UP 
1 = STOP/slat adjustment DOWN 

 

77 

Move to position 

Blind Output A,B  

Shutter Output A,B  

1 byte 

DPT 5.001 

C, W, T 

This group object is enabled if the 

Mode Output

 parameter is set to 

Blind

 in the 

Output A,B: Mode

 parameter window. 

This group object is used for movement to and feedback of a determined position (0 = top, 255 = bottom).  

If this group object receives a telegram the blind is moved to the position corresponding to the received value. 

After the target position is reached, the slats will assume the same position as before the movement started. If an 

Adjust slat 

0…255

 telegram is received during movement, the slats move to the received target position. 

Telegram value: 

0  

= upper 

…  

= Intermediate position 

255   = lower 

 

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды