manualshive.com logo in svg

ABB i-bus KNX IPS/S 3.5.1, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus KNX IPS/S 3.5.1 Скачать руководство пользователя страница 19

ABB i-bus

®

 KNX 

Commissioning 

 

 

IPS/S 3.5.1 | 9AKK107680A8655 EN Rev. A   19 

3 

Commissioning 

The IPS/S is parametrized using the application and Engineering Tool Software (ETS). 
The application can be found under 

Manufacturers/ABB/System Infrastructure and Interfacing/IP Routers 

and Interfaces

. 

For parameterization purposes, a PC or laptop with ETS and a connection to the KNX bus are required. 

 

 

3.1 

Overview 

The IPS/S is parametrized using Engineering Tool Software (ETS 5 version 5.7.4 or higher). 

 

 

3.2 

Parameters 

This chapter describes the parameters of the IP Interface Secure using the parameter windows. 

 

Parameter window 

IP settings 

All parameters for the device are set in the Properties window of ETS. 

 

 

Note: The device name, IP address and tunneling servers are set in the Properties window of ETS. 

 

 

Содержание i-bus KNX IPS/S 3.5.1































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды