ABB i-bus KNX ABA/S 1.2.1 Скачать руководство пользователя страница 15

Страница: 15 / 116

ABB i-bus

KNX

Product Overview

ABA/S 1.2.1 | 2CDC509086D0201 15

3.3.3

Operating and display elements

Button/LED

Description

LED indicator

Assignment of the physical
address

On: Device is in programming mode

Off: No auxiliary voltage (24 V or PoE) available

On: System initialized

Flashing slowly (1 Hz): System starting up

Flashing quickly (4 Hz): Error

LAN/LINK

On: Auxiliary voltage and Ethernet connection
available

Flickering: Data traffic via LAN

On: Auxiliary voltage and KNX connection
available

Flickering: Data traffic via KNX/TP

Reset (behind label carrier)

Press for less than 2 seconds: no reaction.

Press for 2 to 10 seconds: device restart. Retains
configuration and last states.

Press for more than 10 seconds: factory reset.
Deletes configuration and all states.

Table 4: Operating and display elements

Note

Device restart and factory reset are only possible when bus voltage and auxiliary voltage are applied.

Note

A firmware update cannot be undone after a factory reset.

Содержание i-bus KNX ABA/S 1.2.1





















































































































Результаты поиска

Содержание i-bus KNX ABA/S 1.2.1

Отзывы:

Бренды по названию

Популярные бренды

ABB i-bus KNX ABA/S 1.2.1, Руководство по эксплуатации продукта

Результаты поиска

Содержание i-bus KNX ABA/S 1.2.1

Отзывы:

Бренды по названию

Популярные бренды