manualshive.com logo in svg

ABB i-bus EIB, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus EIB Скачать руководство пользователя страница 21

ABB i-bus

®

 EIB / KNX 

Application and planning

 

 

3.4 Operating 

mode: 

“Fan coil control” 

 

3.4.1 Terms 

A fan coil unit is connected to a central heating and cooling supply and 
generates the required temperature room by room. A room can be heated, 
cooled and ventilated with a fan coil unit. 

3.4.2 

Structure of an HVAC 
system with fan coil units 

An HVAC system with fan coil units (HVAC = Heating, ventilation, air-
conditioning) consists of a central hot and cold water supply. Fan coil units 
are mounted in the rooms and directly connected to the hot and cold water 
circulation loops. 

Fan Coil Units 

Hot water circulation loop 

Cold water circulation loop 

Boiler and cold 
water supply 

 

Fig. 8: Structure of an HVAC system with fan coil units 

3.4.3 

Structure of a fan coil unit 

The heat exchangers and the fan are the most important components of a 
fan coil unit. The hot or cold water flows into the heat exchangers depending 
on the room temperature required. The flow of water through the heat 
exchangers is controlled via the valves. 

 
 
 

 

Valves 

Drip tray 

 Fan 

Motor 

Switchbox 
with controller 

Filter Heat 

exchanger 

 

Fig. 9: Structure of a fan coil unit 

The fan blows air past the heat exchangers and through a filter into the 
room. The air is heated or cooled at the heat exchangers and thus generates 
the required room temperature. The fan is driven by a motor. The motor and 
the valves are regulated by the Fan Coil Controller FC/S 1.1. 

The condensed water that is generated by the cooling process is collected in 
a drip tray. 

© 2004 ABB STOTZ-KONTAKT GmbH 

 

21

 

Содержание i-bus EIB































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды