ABB HT610063 Скачать руководство пользователя

Страница: 132 / 148

Operation Manual / A170-M.. - A175-M..

13 Spare parts / 13.1 Ordering spare parts

HZTL4033_EN

Rev.K

January 2022

Spare parts

13.1

Ordering spare parts

CAUTION

Spare part storage

All spare parts that were ordered together with the turbocharger must be
kept intact and ready for use.

Carefully clean any rusted parts and grease them.

Please quote the following data when making queries and ordering spare parts:

Turbocharger type

Serial number of the turbocharger

Designation and part number.

Spare parts can be ordered from any ABB Turbocharging Service Station.

If different model variants are not taken into account in this document, contact an ABB
Turbocharging Service Station.

Dispose of placed and unusable parts in an environmentally-friendly and professional
manner in accordance with the local regulations.

Dispose of the packaging of new parts in an environmentally-friendly and professional
manner in accordance with the local regulations.

Required customer spare part set (97070)

For the work described in the Operation Manual, the customer spare part set (97070) is re-
quired. These parts are only available in the complete set.

Customer spare part set

97070

Designation

Quantity

25013

Socket screw

25014

Washer

42012

O-ring

42041

Gasket

42045

Gasket

42059 / 42064

Hexagon-head screw

56014

Hexagon-head screw

56015

Locking washer

57005

Hexagon-head screw

61037

Hexagon nut

61069

Hexagon-head screw

77015

Socket screw

77040

O-ring

86506

O-ring (speed sensor)

Table 60: Customer spare part set (97070)

Page

130

146

Содержание HT610063



















































































































































Результаты поиска

Содержание HT610063

Отзывы:

Похожие инструкции для HT610063

Бренды по названию

Популярные бренды

ABB HT610063, Руководство по эксплуатации

Результаты поиска

Содержание HT610063

Отзывы:

Похожие инструкции для HT610063

Бренды по названию

Популярные бренды