ABB HT608782 Скачать руководство пользователя | Manualshive

Страница: 44 / 148

background image

Operation Manual / A170-M.. - A175-M..

5 Monitoring during operation / 5.1 Oil pressure, oil temperature

© Copyright 2021 ABB. All rights reserved.

HZTL4033_EN

Rev.I

November 2021

Lubricating oil temperature at the inlet

CAUTION

Machine damage

If the oil temperature at the oil inlet exceeds the admissible range, this may
lead to engine damage.

u

Observe oil temperature at the oil inlet according to the following table.

Status for operation

Oil temperature at the inlet

T

oil,inlet

[°C]

Admissible

< 90

Temporarily admissible (< 1 h)

→

alarm

> 90

Not admissible

→

stop engine

> 95

Table 11: Oil temperature at the inlet

Lubricating oil temperature at the outlet

The oil temperature at the outlet is mainly dependant on:

¡

Lubricating oil temperature and pressure at the oil inlet

¡

Engine load and turbocharger speed

¡

Exhaust gas temperature

The maximum admissible oil temperature at the outlet is listed in the following table. The
specified oil outlet temperature is to be considered as alarm value for the turbocharger op-
eration and must be monitored according to the current regulations.

Status for operation

Oil temperature at the outlet

T

oil,outlet

[°C]

Admissible

≤

135

Temporarily admissible

→

alarm

> 135

Not admissible

→

stop engine

> 155

Table 12: Oil temperature at the outlet

If the turbocharger has been operated for a longer period of time outside the admissible
range, ABB Turbocharging recommends having the turbocharger inspected by an ABB Tur-
bocharging Service Station.

Page

42

/

146

«
...
42
43
44
45
46
...
»

Содержание HT608782





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT608782

Бренд: MacDon Страницы: 46

Бренд: MacDon Страницы: 82

Бренд: Mac Medical Страницы: 2

Бренд: MACDEV Страницы: 8

Mentor Touch ET750

Бренд: MAC TOOLS Страницы: 24

Бренд: MA lighting Страницы: 10

Бренд: Qlight Страницы: 3

Бренд: qtran Страницы: 2

Бренд: Q-Optics Страницы: 2

Бренд: UNIS Страницы: 16

Bathomatic Basic

Бренд: Unique Automation Страницы: 10

Бренд: Additel Страницы: 139

QUICK-ALIGN Vari-Flex

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 2

Бренд: Össur Страницы: 8

Бренд: Delfield Страницы: 24

Бренд: American DJ Страницы: 8

Бренд: COURANT Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды