ABB HT564844 Скачать руководство пользователя страница 22

Страница: 22 / 128

Operation Manual / TPL67-C.. - TPL71-C..

Safety

Definition of mandatory signs

2.3

Page 20

Apr

il 2016

L2488_

ion

Definition of mandatory signs

2.3

To be worn at all times

Protective clothing

Safety footwear against

mechanical hazards

To be worn according to the specific work

Safety glasses

Safety goggles

Safety gloves against
- mechanical hazards
- chemical hazards
- heat hazards

Respiratory mask against
- dust
- gases

Safety helmet

Ear protection

Definition of Safety instructions

2.4

The following symbols and terms used in this manual concern safety or

refer to possible hazards:

WARNING

Definition of warning
Serious personal injuries and even accidents with fatal consequences

may occur if work and operating instructions marked with this symbol

and the word WARNING are either not followed or not followed precise-

ly.



Warning signs must be observed at all times.

CAUTION

Definition of caution
Serious machine or property damage may occur if work and operating

instructions marked with this symbol and the word CAUTION are either

not followed or not followed precisely.



Caution signs must be observed at all times.

2.3

2.4

Содержание HT564844
































































































































Результаты поиска

Содержание HT564844

Отзывы:

Похожие инструкции для HT564844

Бренды по названию

Популярные бренды

ABB HT564844, Руководство по эксплуатации

Результаты поиска

Содержание HT564844

Отзывы:

Похожие инструкции для HT564844

Бренды по названию

Популярные бренды