ABB GOE 2600 Скачать руководство пользователя страница 14

Страница: 14 / 84

Installation and commissioning guide

1ZSC000563-AAF EN, REV. 4, 2021-06-23

Long term storage, more than 6 months

•

The bushing can be stored outdoors, if it is in the transport box.
Keep the transport box protected from water, when the bushing is stored outdoors.

•

Keep the bushing dry, clean and protected against mechanical damage.

•

Lift the bushing to the vertical position, and put it in a safe stand.
–

As an alternative: keep the bushing in the transport box and lift it to an inclined position, with the
top end upwards and at an angle of at least 7°.

The bushing is delivered from Hitachi ABB Power Grids in a transport box, and the bushing is held in place
by support blocks in the box.

The transport box is marked with

Top end,

this identifies the end to lift when the bushing is in storage.

G006947

3.4 Lifting

3.4.1 Lifting the transport box

Overview

G006948

Soft lifting slings

43 Center of gravity

Содержание GOE 2600





















































































Результаты поиска

Содержание GOE 2600

Отзывы:

ABB GOE 2600, Руководство по установке и пусконаладке, Страница: 14 / 84

Результаты поиска

Содержание GOE 2600

Отзывы: