manualshive.com logo in svg

ABB Feather Duster, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB Feather Duster Скачать руководство пользователя страница 7

 

 

5

3HAW050027150 Revision: C    

© 

Co

py

rig

h

t 201

3-

101

6 ABB. All righ

ts reser

v

ed.

0.0.1. Overview of this manual

About this manual

This manual contains instructions for:

•

the characteristics of the Feather Duster

•

mechanical and electrical installation instructions for the Feather Duster

•

maintenance instructions for the Feather Duster

•

spare parts

Usage

This manual should be used when working during:

•

installation, from lifting the Feather Duster to its work site and securing it to the 

foundation, to making it ready for operation

•

maintenance work

•

repair work.

Who should read this manual?

This manual is intended for: 

•

installation personnel

•

maintenance personnel

•

repair personnel.

Prerequisites

A maintenance /repair/ installation craftsman working with an ABB Feather Duster must:

•

be trained by ABB and have the required knowledge of mechanical and electrical 

installation/repair/maintenance work.

Organization of chapters

The manual is organized in the following chapters:

Chapter

Content

Safety

Safety information that must be read through before performing 
any installation or service work on the Feather Duster. Contains 
general safety aspects as well as more specific information 
about how to avoid personal injuries and damage to the product.

Description and technical 
details

Specifications and characteristics of the Feather Duster.

Installation

Information for installing the Feather Duster and connection to 
the control system.

Unpacking, acceptance 
and handling

Information relative to the steps following the reception of the 
Feather Duster, until its installation.

Maintenance

Step-by-step procedures that describe how to perform 
maintenance of the Feather Duster. Based on a maintenance 
schedule that may be used in the work of planning periodical 
maintenance.

Spare parts

List of the spare parts available for the Feather Duster.

Содержание Feather Duster























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды