ABB Feather Duster Скачать руководство пользователя страница 28

Страница: 28 / 150

1 Safety

1.4.8. Translate the information on safety and information labels

3HAW050027150 Revision: C

rig

t 201

101

6 ABB. All righ

ts reser

ed.

1.4.8. Translate the information on safety and information labels

Labels on the product

Both the manipulator and the controller are marked with several safety and information

labels, containing important information about the product. The information is useful for all

personnel handling the robot system, e.g. during installation, service or operation.

Translation possibilities

The labels fitted to the product contain space for adding a fourth language underneath the

three standard languages (English, German and French).

Add a local language to the label by:

•

using a transparent sticker over the standard label with text added in a fourth language.

Drawings detailing the design (text, figure, dimensions) of the standard labels can be

ordered from ABB. Notice that each label is identified according to the article number

located in the lower corner of the label.

Example of transparent sticker

The figure below shows the location of the free space on one of the labels on the robot, where

the fourth language can be added. The figure also shows a transparent sticker, containing the

text in Swedish.

xx0500002517

Free space for adding a fourth language

Содержание Feather Duster













































































































































Результаты поиска

Содержание Feather Duster

Отзывы:

Бренды по названию

Популярные бренды

ABB Feather Duster, Руководство по эксплуатации продукта

Результаты поиска

Содержание Feather Duster

Отзывы:

Бренды по названию

Популярные бренды