ABB FCAN-01 Скачать руководство пользователя

Страница: 38 / 176

38 Start-up

Drive configuration

The following information applies to all drive types compatible with

the adapter module, unless otherwise stated.



CANopen connection configuration

After the adapter module has been mechanically and electrically

installed according to the instructions in chapters

Mechanical

installation

and

Electrical installation

, the drive must be prepared

for communication with the module.
The detailed procedure of activating the module for CANopen

communication with the drive depends on the drive type. Normally,

a parameter must be adjusted to activate the communication. See

the drive-specific start-up sections on pages

and

Once communication between the drive and the adapter module

has been established, several configuration parameters are copied

to the drive. These parameters are shown in the tables below and

must be checked first and adjusted where necessary.

Note:

Not all drives display descriptive names for the configuration

parameters. To help you identify the parameters in different drives,

the names displayed by each drive are given in grey boxes in the

tables.
An example on how to configure PDOs via the CAN bus is given in

section

PDO configuration via the CAN bus

Note:

The new settings take effect only when the adapter module

is powered up the next time or when the fieldbus adapter refresh

parameter is activated.

Data transfer rates supported

The FCAN-01 CANopen adapter module supports the following

CANopen communication speeds: 50 kbit/s, 100 kbit/s, 125 kbit/s,

250 kbit/s, 500 kbit/s, 1 Mbit/s.

Note:

The CANopen standard CiA 301 does not list 100 kbit/s as a

recommended bit rate, and therefore it should not be used in new

installations.

Содержание FCAN-01

















































































































































































Результаты поиска

Содержание FCAN-01

Отзывы:

Похожие инструкции для FCAN-01

Бренды по названию

Популярные бренды

ABB FCAN-01, Руководство пользователя

Результаты поиска

Содержание FCAN-01

Отзывы:

Похожие инструкции для FCAN-01

Бренды по названию

Популярные бренды