ABB FBIP-21 BACnet/IP Скачать руководство пользователя страница 45

Страница: 45 / 74

￭

Binary value object

Present value access
type

Default active/ Inact-
ive text

Description

Default object name

Object
ID

RUN / STOP

Run status of drive

RUN-STOP-Monitor

BV0

REVERSE / FORWARD

Rotational direction of
the motor

Direction-Monitor

BV1

FAULT / OK

Actual fault status of
drive

OK-FAULT-Monitor

BV2

EXT2 / EXT1

Actual control source

EXT1-EXT2-Monitor

BV3

HAND / AUTO

Actual operating
mode

HAND-AUTO-Monitor

BV4

WARNING / OK

Actual warning status

Warning-Monitor

BV5

READY / NOT- READY

Actual ready status

Ready-Monitor

BV7

YES / NO

Actual at setpoint
status

At-Setpoint-Monitor

BV8

ENABLE / DISABLE

Actual run enabled
status

Enabled-Monitor

BV9

RUN / STOP

Command to start
drive

RUN-STOP-Command

BV10

REVERSE / FORWARD

Command to rotation-
al direction

Direction-Command

BV11

ENABLE / DISABLE

Command to Run Per-
missive command

Run- Permissive-Com-
mand

BV12

EXT2 / EXT1

Command to External
1 or External 2

EXT1-EXT2-Command

BV13

RESET / NO

Command to fault re-
set

Fault-Reset-Command

BV14

LOCK / UNLOCK

Actual status of para-
meter lock.

Lock-Parameters

BV17

ON / OFF

Command the drive
into BACnet Control
Override. In this mode
BACnet acquires drive
control from its nor-
mal source.

Control- Override-
Command

BV18

Note: The HAND mode
of the panel has prior-
ity over BACnet Con-
trol Override.

Communication protocol 45

Содержание FBIP-21 BACnet/IP










































































Результаты поиска

Содержание FBIP-21 BACnet/IP

Отзывы:

Бренды по названию

Популярные бренды

ABB FBIP-21 BACnet/IP, Руководство пользователя

Результаты поиска

Содержание FBIP-21 BACnet/IP

Отзывы:

Бренды по названию

Популярные бренды