manualshive.com logo in svg

ABB EL6010, Руководство оператора

Поделиться
Скачать
ABB EL6010 Скачать руководство пользователя страница 55

 

42/24-30 EN Rev. 1 

EL6010 Gas Analyzer in Category 2G Operator’s Manual 

53 

Analyzer Units 

  

EL6010-Uras14 
Infrared Analyzer Unit 

The EL6010-Uras14 infrared analyzer unit uses the NDIR (Non-Dispersive Infrared 
Absorption) technique. It measures concentrations of one or two sample compo-
nents. 

  

EL6010-Magnos106 
Oxygen Analyzer Unit 

The EL6010-Magnos106 oxygen analyzer unit’s measurement principle is based 
on the specific paramagnetic behavior of oxygen. 

  

EL6010-Caldos17 
Thermal Conductivity 
Analyzer Unit 

The EL6010-Caldos17 thermal conductivity analyzer unit uses the different thermal 
conductivity of individual gases. It measures the concentration of a sample com-
ponent in a binary gas mixture. 

  

Design 

Each analyzer unit consists of the sensor and its associated electronics. 

 
The analyzer unit is built according to the EN 50018 “Flame-proof Enclosure” 
protection type. It is contained in a pressure-tight aluminum cylinder. 

 
All gas connections are routed via flame barriers. The flame barriers and the pipe 
threaded connections are made of 1.4571 steel. 

 
The analyzer unit is connected to the control unit via data transmission and power 
supply cables. The 12- and 3-conductor cables, each 3 meters in length, are 
connected at the factory and are brought into the pressure-tight cylinder via 
pressure-tight cable openings. 

 
Housing protection type is IP 54 (O-ring seals required when mounted horizontally).

  

Housing Purge 

To protect the analyzer unit sensor electronics against the entry of an aggressive 
atmosphere or corrosive sample gas components, a purge gas can flow through 
the pressure-tight cylinder. 

 
The purge gas enters and exits via two flame barriers which are open in the 
interior of the pressure-tight cylinder. 

 
In the EL6010-Magnos106 and EL6010-Caldos17 analyzer units the pressure-tight 
cylinder purge gas outlet is internally joined to the purge gas outlet for the thermo-
stat housing. The thermostat housing purge gas inlet is open. 

 

Note:  The housing purge has no significance for the purposes of EN 50016 

positive pressure containment.

 

  

Calibration 

Essentially the gas analyzer is calibrated manually. External control of calibration 
is possible via the Modbus interface. 

 
The EL6010-Uras14 infrared analyzer unit can be equipped with optional gas-filled 
calibration cells that extensively eliminate reliance on test gases. 

 
Because of its very low sensitivity drift, the EL6010-Magnos106 oxygen analyzer 
unit routinely requires only a zero calibration, if the measuring range is larger than 
0 to 5 Vol.-% O

2

. Nitrogen or ambient air are used for this. 

  

Содержание EL6010













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды