ABB EL6010 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 76

background image

16

EL6010 Gas Analyzer in Category 2G Operator’s Manual

42/24-30 EN Rev. 1

Connect Electrical Lines – Safety Precautions

CAUTION!

Follow all applicable national safety regulations for the preparation and
operation of electrical devices as well as the following safety precautions!

Potential
Compensation

The external potential compensation connections of the control unit and the
analyzer unit must be connected to the local potential compensation point.
The connection to the local potential compensation point must be made
before all other connections. Minimum conductor section = 4 mm

2

.

The gas analyzer can be hazardous if the protective lead is interrupted inside
or outside the gas analyzer or if the protective lead is disconnected.

Securing
Electrical Lines

All electrical wiring, including the connections between the analyzer unit and
the control unit, must be firmly secured.

Shielded Lines

Shielded lines must be routed through the metal wiring connectors. The
shield braid must be placed on the cable connectors.

Unused
Cable Connections

Only the manufacturer’s original equipment plugs should be used to close off
the threaded cable connections. Unused cable connectors must be closed
off with factory-provided plugs. Securely tighten the cap nuts on the unused
cable connectors (torque to 2.5 Nm).

Before the Power
Supply is Connected

Before the power supply is connected, make sure the power line voltage is in
the permissible range 85 to 250 VAC for operation of the gas analyzer.

«
...
16
17
18
19
20
...
»

Содержание EL6010













































































Отзывы:

Нет отзывов

Похожие инструкции для EL6010

Workstation Monitor 724

Бренд: 3M Страницы: 21

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 24

Бренд: 3M Страницы: 2

SoundPro SE Series

Бренд: 3M Страницы: 293

Бренд: Bacharach Страницы: 60

Бренд: Bacharach Страницы: 4

Бренд: Bacharach Страницы: 17

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 110

Portatone PSR-5700

Бренд: Yamaha Страницы: 79

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 82

Бренд: Yamaha Страницы: 108

Бренд: Chroma Страницы: 63

Ranger TDR VDV501-090

Бренд: Klein Tools Страницы: 44

Бренд: PRONIVO Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды