ABB DressPack IRB6650S Скачать руководство пользователя страница 210

Страница: 210 / 390

3.3 Inspection activities

3.3.1 Preventive inspection of all cables, DressPack

Cables in the DressPack system

There are many different cables used in the DressPack system. The different cables
used are listed in Spare parts section.

The inspection activities described below are a general description, and does not
refer to any specific cable.

Required equipment

Note

Art. no.

Equipment

The contents are defined in section

Toolkits,

DressPack/SpotPack on page 355

3HAC17290-7

Standard Toolkit,
DressPack/SpotPack

Inspection

The procedure below details how to inspect all cables included in the SpotPack
system.

This instruction applies to:

•

DressPack upper arm and cables and hoses contained within

•

DressPack lower arm and cables and hoses contained within

•

DressPack lower/upper arm and cables and hose contained within

•

DressPack floor and cables and hoses contained within.

Note

Action

DANGER

Turn off all:

•

electric power supply

•

hydraulic pressure supply

•

air pressure supply

to the robot, before entering the robot
working area.

Clean if required as detailed in section

Cleaning, DressPack upper arm on
page 223

Make sure that the unit is clean and not
overly contaminated.

Recommended tightening torques are
specified in section

Screw joints on

page 351

Make sure that all bolts are fastened.

Re-tighten if necessary.

Make sure that all connections are fastened.

Re-tighten if necessary.

Make sure that all hose connections are
fastened and that there are no leaks.

Continues on next page

210

Product manual - DressPack/SpotPack IRB 6650S

3HAC055424-001 Revision: C

3 Maintenance

3.3.1 Preventive inspection of all cables, DressPack

Содержание DressPack IRB6650S






































































































































































































































































































































































































Результаты поиска

Содержание DressPack IRB6650S

Отзывы:

ABB DressPack IRB6650S, Руководство по эксплуатации продукта, Страница: 210 / 390

Результаты поиска

Содержание DressPack IRB6650S

Отзывы: