ABB CPS6000, Руководство по эксплуатации продукта

Страница: 160 / 201

Page 160
© Copyright 2021 ABB. All rights reserved.
Alarm Thresholds/Relays Related Commands
obj,attr description sta cha ope type range of values
macf1,sev Multiple AC fail severity x x text “ MAJ ”, “ MIN ” , or “ RO"
mcm1,acc Major communication relay x x text “ R1 ” ,“ R2 ”, “ R3 ”, “ R4 ”, or “”
mcm1,ast Major communication alarm state x number 0:not active 1:active
mcm1,sev Major communication severity x x text “ MAJ ”, “ MIN ” , or “ RO"
mrfa1,acc Multiple rectifier fail relay x x text “ R1 ” ,“ R2 ”, “ R3 ”, “ R4, ” or “”
mrfa1,ast Multiple rectifier fail alarm state x number 0:not active 1:active
mrfa1,sev Multiple rectifier fail severity x x text “ MAJ ”, “ MIN ” , or “ RO"
osa1,acc Open string alarm relay x x text “ R1 ” ,“ R2 ”, “ R3 ”, “ R4 ”, or “”
osa1,ast Open string alarm state x number 0:not active 1:active
osa1,sev Open string alarm severity x x text “ MAJ ”, “ MIN ” , or “ RO"
rfa1,acc Rectifier fail relay x x text “ R1 ” ,“ R2 ”, “ R3 ”, “ R4 ”, or “”
rfa1,ast Rectifier fail alarm state x number 0:not active 1:active
rfa1,sev Rectifier fail severity x x text “ MAJ ”, “ MIN ” , or “ RO"
rls1,acc Rectifier redundancy loss relay x x text “ R1 ” ,“ R2 ”, “ R3 ”, “ R4 ”, or “”
rls1,ast Rect redundancy loss alarm state x number 0:not active 1:active
rls1,sev Rect redundancy loss severity x x text “ MAJ ”, “ MIN ” , or “ RO"
scd1,acc Battery voltage imbalance relay x x text “ R1 ” ,“ R2 ”, “ R3 ”, “ R4 ”, or “”
scd1,ast Battery voltage imbalance alarm
state
x number 0:not active 1:active
scd1,sev Battery voltage imbalance severity x x text “ MAJ ”, “ MIN ” , or “ RO"
tpa1,acc Thermal probe fail relay x x text “ R1 ” ,“ R2 ”, “ R3 ”, “ R4 ”, or “”
tpa1,ast Thermal probe fail alarm state x number 0:not active 1:active
tpa1,sev Thermal probe fail severity x x text “ MAJ ”, “ MIN ” , or “ RO"
vmf1,acc Voltage module fail relay x x text “ R1 ” ,“ R2 ”, “ R3 ”, “ R4 ”, or “”
vmf1,ast Voltage module fail alarm state x number 0:not active 1:active
vmf1,sev Voltage module fail severity x x text “ MAJ ”, “ MIN ” , or “ RO"
vsf1,acc Sense voltage fail relay x x text “ R1 ” ,“ R2 ”, “ R3 ”, “ R4 ”, or “”
vsf1,ast Sense voltage fail alarm state x number 0:not active 1:active
vsf1,sev Sense voltage fail severity x x text “ MAJ ”, “ MIN ” , or “ RO"
The previous table outlines the various alarms that are available through the QS840A controller. Refer
to Alarm Relays in Appendix C for more details. The QS840A controller is provided with two severity
relays and two relays that may be assigned to any combination or all of the alarms noted above.
The controller is shipped with PMN assigned to Alarm Relay 2 and PMJ to Alarm Relay 1. Also, for each
alarm condition noted above, the factory severity is noted in bold. The user may change the severity of
configurable alarms from the factory set severity. Note that the alarms noted above may also be
assigned a severity of RO (Record Only). If so assigned, the alarm condition will be transmitted without
any PMJ or PMN severity.
The following is a brief explanation of the alarm conditions.
Battery on Discharge: The battery on discharge alarm is asserted when the controller detects the plant
bus voltage going below the Battery on Discharge thresholds set by the user.
High Voltage: The high voltage alarm is asserted when the controller detects the plant bus voltage
going above the High Voltage thresholds set by the user.