ABB Aztec 600 Color Скачать руководство пользователя

Страница: 64 / 110

Aztec 600 aluminium, ammonia, color, iron, manganese, phosphate

Single- and multi-stream colorimetric analyzers

12 Diagnostic Information and Icons

IM/AZT6CR–EN Rev. R

12.3.2

Alarm Event Log – Icons

12.3.3 Status Icons

Note.



flashing

red alarm icon indicates an active and

unacknowledged alarm.



continuous

red alarm icon indicates an active and

acknowledged alarm.

Icon

Event

High process alarm – active/inactive

Low process alarm – active/inactive

High latch alarm – active/inactive

Low latch alarm – active/inactive

High annunciate alarm – active/inactive

Low annunciate alarm – active/inactive

Clean-in-progress alarm – active/inactive

In sample alarm

Out of sample alarm

Daylight saving start/end changed

Alarm acknowledged

Operator message

Note.

Status icons are displayed in the Status Bar – see

Fig. 2.1, page 8.

Icon

Event

Historical review active

External archive media on-line with % used
indication

External archive media off-line with % used
indication

External archive media not inserted
(yellow flashing exclamation mark)

Media update in progress. Do not remove media
while this symbol is displayed

External media 100% full, archiving stopped
(green/grey icon, flashing white cross)

Warning! Too many files (green icon – media
online, grey icon – media offline)

Содержание Aztec 600 Color















































































































Результаты поиска

Содержание Aztec 600 Color

Отзывы:

Похожие инструкции для Aztec 600 Color

Бренды по названию

Популярные бренды

ABB Aztec 600 Color, Руководство пользователя

Результаты поиска

Содержание Aztec 600 Color

Отзывы:

Похожие инструкции для Aztec 600 Color

Бренды по названию

Популярные бренды