ABB AV1 Скачать руководство пользователя страница 45

Страница: 45 / 126

CALIBRATION

CALIBRATION FOR PARTICULAR APPLICATION

4 - 3

Span Adjustment

Setting the span normally requires the alignment of the 100 per-
cent radial line of the cam with the center of the cam roller.

Use the following steps to adjust the span:

1. Depending on the nomenclature type, apply one of the follow-
ing input signals:

Types AV11/5

Apply 103.4 kPa (15.0 psig). The actuator should move to its
fully opened position.

Type AV12/6

Apply 186.2 kPa (27.0 psig). The actuator should move to its
fully opened position.

Type AV2

Apply 20 mA. The actuator should move to its fully opened
position.

2. To adjust the span, loosen the span adjustment screw (Fig.

4-1

) using a

-inch Allen wrench.

3. Slide the span adjustment assembly (Fig.

4-1

) in the appropri-

ate direction until the actuator moves to align the 100% radial line
with the center of the cam roller (toward pilot valve increases span
of actuator).

4. Tighten the span adjustment screw.

CALIBRATION FOR PARTICULAR APPLICATION

The following positioner adjustments may be used to tailor the
operation of the actuator to meet application requirements.

Figure 4-2. Cam Roller Alignment

T00771A

CAM FOLLOWER ARM

CAM ROLLER

CAM

⁄

Содержание AV1































































































































Результаты поиска

Содержание AV1

Отзывы:

Похожие инструкции для AV1

Бренды по названию

Популярные бренды

ABB AV1, Руководство по эксплуатации

Результаты поиска

Содержание AV1

Отзывы:

Похожие инструкции для AV1

Бренды по названию

Популярные бренды