ABB ARG600 Single SIM Variant страница 35 Скачать руководство пользователя | Manualshive

Страница: 35 / 64

background image

Section 6

Serial port configuration

6.1

Configuring serial ports

1.

In the left pane, under

Serial Port and I/O

, click

General Configuration

.

2.

Select an

Application Mode

for each serial port.

•

Serial Gateway: Transparent connection to any serial device

•

IEC-104: IEC-101 to IEC-104 conversion with IEC-101 serial device
protocol

•

Modbus: Modbus conversion with Modbus/RTU or Modbus/ASCII
serial device protocol

6.2

Serial gateway

The serial gateway feature enables data from the serial port attached device to be
routed to Ethernet/mobile network (serial over IP) and vice versa. Serial gateway
processes the transmitted data transparently and does not alter it any way except for
buffering it for transmission. Because of the transparent communication, any
protocols can be used in actual communication between nodes.Serial gateway
configuration depends on used protocols.

1MRS758456 H

Section 6

Serial port configuration

ARG600 Single SIM Variant

29

User Manual

«
...
33
34
35
36
37
...
»

Содержание ARG600 Single SIM Variant

































































Отзывы:

Нет отзывов

Похожие инструкции для ARG600 Single SIM Variant

Бренд: ICP DAS USA Страницы: 71

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 19

Бренд: Gree Страницы: 12

Бренд: LG Страницы: 11

AC Smart BACnet

Бренд: LG Страницы: 88

BECON HVAC BACnet PQNFB17C0

Бренд: LG Страницы: 118

Бренд: LG Страницы: 220

Бренд: LG Страницы: 481

Бренд: LG Страницы: 2

Бренд: Nokia Страницы: 5

Бренд: Nokia Страницы: 25

Бренд: Nokia Страницы: 56

Бренд: Nokia Страницы: 109

Бренд: Nokia Страницы: 129

Бренд: TP-Link Страницы: 63

Бренд: HELIX Страницы: 12

Бренд: ViewSonic Страницы: 58

Бренд: Technicolor Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды