ABB AKD-10 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 77

ABB AKD-10 Скачать руководство пользователя страница 25

4. Carefully lower the breaker onto the rails, making sure both rollers on each side land
centrally on each rail such that the full weight of the breakers is fully supported by
the rails.
5. Remove the lifting bar, any lifting eye hooks and chains.

Note 1: Make sure the J hook of the lifting bar is secured in the front window on both
Side sheets of the breaker as shown in fig 25. This will ensure the breaker is
better balanced when lifted.

Note 2: The size of the slot at the top of the lifting bar is 0.7” wide and 1” high. Hooks
used in the hoist should be suitable to engage with this slot size. After loading
on rails of fully withdrawn position remove the eye bolts or lifting means.
Note 3: Use of Lifting bar or spreader bar allows to reach the top most switchgear
Compartment easily, so it is the recommended method.
Note 4: As an alternate to above lifting process, eye bolts, chain attached to eye bolts
through S hook, and connector can be used to lift the WavePro Retrofill Breaker.
Examples of an eye bolt and connector are shown in fig’s 26 and 27. Insert M10

Figure 25

Figure 24

AKD-10, Using ABB Lifting bar and hoist

AKD-10, Using ABB Lifting bar and hoist

C

«
...
23
24
25
26
27
...
»

Содержание AKD-10














































































Отзывы:

Нет отзывов