ABB AKD-10 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 77

ABB AKD-10 Скачать руководство пользователя страница 20

Turn off all power to switchgear. Tagout and
lockout main source, up-stream or main
breaker.
Failure to comply with these instructions will
result in death or serious injury from severe
burns caused by arc flashing that has
exceedingly high temperatures.
Always wear personal protection equipment
according to OSHA standards and appropriate
to the severity of potential burns.

Ensure only qualified personnel install, operate, service, and maintain all electrical
equipment.

Do not walk or remain under any heavy
assembly while hoisted above head as the
chains securing the assembly may give way.

Ensure lifting equipment has capability for device being lifted.
Wear hard hat, gloves, and safety shoes.
Failure to comply with these instructions could result in serious injury

.

PRODUCT DAMAGE

Ensure circuit breaker and its accessories are always
used within their designated ratings.
Do not allow the circuit breaker to hit a hard surface
while handling.
Do not drag or slide the circuit breaker across a hard
or rough surface.

A factory-installed rejection feature prevents mismatching circuit breakers and

cassettes/ substructure, preventing the insertion of a circuit breaker with a lower

rating

into a higher rated cassette/substructure, or the insertion of a higher rated
circuit breaker into a lower rated cassette/substructure.

By following the procedures below, you should be able to install the breaker with minimum
effort and time.

Danger

Caution

Notice

Unpack Circuit Breaker

C

«
...
18
19
20
21
22
...
»

Содержание AKD-10














































































Отзывы:

Нет отзывов