ABB ACS880-304 +A018 Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 280

ABB ACS880-304 +A018 Скачать руководство пользователя страница 107

Electrical installation 107

Connecting the control cables



Connection diagram

See the final circuit diagrams by the designer of the cabinet-installed drive. For the default
I/O connection diagram of the supply unit, see section

Default I/O connection diagram of

the supply unit

on page



Connection procedure

This section contains instructions on how to connect external control cables to the supply
unit.

WARNING!

Only qualified electricians are allowed to do this work. Read the

complete safety instructions of the drive. Ignoring the instructions can cause
physical injury or death, or damage to the equipment.

WARNING!

Apply grease to stripped aluminum conductors before attaching them

to non-coated aluminum cable lugs. Obey the grease manufacturer’s instructions.
Aluminum-aluminum contact can cause oxidation in the contact surfaces.

1. Disconnect the drive from the AC power line and make sure it is safe to start the work.

Obey the instructions in section

Basic electrical safety precautions

on page

2. Open the door of the cabinet and remove the shrouds (if any).

3. Run the external control cables into the inside of the cabinet.

•

Run the cables between the EMI conductive cushions (a), or the equipment that
you can use for the 360 degree grounding of the cable shield. Strip the cable at
this location to enable proper connection of the bare shield and the cushions.
Tighten the cushions firmly onto the cable shields.

•

Seal the cable lead-through with a grommet.

4. Run the cables to the appropriate terminals. Wherever possible:

•

Use the existing cable trunking in the cabinet.

•

Use sleeving wherever the cables are laid against sharp edges.

•

Tie the cables to provide strain relief.

5. Cut the cables to suitable length. Strip the cables and conductors.

6. Twist the cable shields into bundles and connect them to the ground terminal nearest

to the terminal block. Keep the unshielded portion of the cables as short as possible.

7. Connect the conductors to appropriate terminals. For the tightening torques of the

BCU control unit I/O terminals, see section

Default I/O connection diagram of the

on page

.

8. Fasten the shrouds (if any) and close the doors.

«
...
105
106
107
108
109
...
»

Содержание ACS880-304 +A018

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды