ABB ACS880-1604 Скачать руководство пользователя страница 104

Страница: 104 / 222

104 Maintenance



Replacing the roof fan for IP54 cabinet

Cabinets with ABB air outlet kits

WARNING!

Only qualified electricians are allowed to do this work.

Read the complete safety instructions given in

Safety instructions for

ACS880 multidrive cabinets and modules

(3AUA0000102301 [English])

before you service the drive. If you ignore them, injury or death, or

damage to the equipment can occur.

WARNING!

Wear protective gloves and long sleeves! Some parts have sharp

edges.

1. Disconnect the drive from the AC power line and DC/DC converter from the energy

storage and obey the instructions in section

Electrical safety precautions

on page

See

Disconnecting the DC/DC converter with DC switch/disconnector

on page

2. The instruction mentioned for each air outlet kit in section

Air outlet kits

on page

143

contains an exploded view of the outlet. Remove all gratings and filters, and finally
remove the plate on top of the outlet. Unscrew all necessary screws securing the fan
and remove it.

3. Install new fan in reverse order.

Cabinets with other fan types

WARNING!

Only qualified electricians are allowed to do this work. Read

the complete safety instructions given in

Safety instructions for ACS880

multidrive cabinets and modules

(3AUA0000102301 [English]) before

you service the drive. If you ignore them, injury or death, or damage to

the equipment can occur.

WARNING!

Wear protective gloves and long sleeves! Some parts have sharp

edges.

1. Disconnect the drive from the AC power line and DC/DC converter from the energy

storage and obey the instructions in section

Electrical safety precautions

on page

2. Follow the instructions of the manufacturer of the air outlet or enclosure system.

Содержание ACS880-1604































































































































































































































Результаты поиска

Содержание ACS880-1604

Отзывы:

Бренды по названию

Популярные бренды

ABB ACS880-1604, Руководство по оборудованию

Результаты поиска

Содержание ACS880-1604

Отзывы:

Бренды по названию

Популярные бренды