ABB ACS880-04F Скачать руководство пользователя страница 73

Страница: 73 / 172

Guidelines for planning the electrical installation 73



Example bypass connection

An example bypass connection is shown below.

Switching the motor power supply from drive to direct-on-line

1. Stop the drive and the motor with the drive control panel (drive in the local control

mode) or the external stop signal (drive in the remote control mode).

2. Open the main contactor of the drive with S11.

3. Switch the motor power supply from the drive to direct-on-line with S40.

4. Wait for 10 seconds to allow the motor magnetization to die away.

5. Start the motor with S41.

Drive main switch

Bypass circuit breaker

Drive main contactor

Bypass contactor

Drive output contactor

S11

Drive main contactor on/off control

S40

Motor power supply selection (drive or direct-on-line)

S41

Start when motor is connected direct-on-line

S42

Stop when motor is connected direct-on-line

Содержание ACS880-04F













































































































































































Результаты поиска

Содержание ACS880-04F

Отзывы:

ABB ACS880-04F, Руководство по оборудованию, Страница: 73 / 172

Результаты поиска

Содержание ACS880-04F

Отзывы: