ABB ACS180 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 392

ABB ACS180 Скачать руководство пользователя страница 51

Program features 51



Scalar motor control

Scalar motor control is the default motor control method. It is suitable for applications
which do not require the control accuracy available in vector control. In scalar control,
you control the drive output frequency reference, and you do not need to do any
motor identification at the first start.

ABB also recommends to activate scalar motor control mode in the following special
situations:

• In multimotor drives: 1) if the load is not equally shared between the motors, 2) if

the motors are of different sizes, or 3) if the motors are going to be changed after
motor identification (ID run)

• If the nominal current of the motor is less than 1/6 of the nominal output current of

the drive

Note:

Do not activate the motor phase loss fault (

Motor phase loss

) as the

drive cannot measure the motor current accurately.

• If the drive is used without a motor connected (for example, for test purposes)
• If the drive runs a medium-voltage motor through a step-up transformer.

In scalar control, some features are not available.

See also section

Operating modes of the drive

on page

IR compensation for scalar motor control

IR compensation (also known as
voltage boost) is available only when
the motor control mode is scalar. When
IR compensation is activated, the drive
gives an extra voltage boost to the
motor at low speeds. IR compensation
is useful in applications that require a
high break-away torque.

In vector control, no IR compensation is
possible or needed as it is applied
automatically.

Settings and diagnostics

Parameter group

28 Frequency reference chain

(page

Paramters

IR compensation

) and

Motor control mode

(page

Events: -

Motor voltage

f

(Hz)

IR compensation

No compensation

ACS180 FW.book Page 51 Tuesday, March 9, 2021 2:25 PM

«
...
49
50
51
52
53
...
»

Содержание ACS180









































































































































































































































































































































































































Отзывы:

Нет отзывов