ABB ACS180-04S-03A7-1 Скачать руководство пользователя страница 22

Страница: 22 / 192

Quick installation and commissioning flowchart

See

Task

Type designation key (page 32)

Identify the frame size: R0, R1, R2, R3 or R4.

Guidelines for planning the electrical
installation (page 43)

Technical data (page 97)

Plan the installation.

Check the ambient conditions, ratings and required
cooling air flow.

Unpacking the delivery (page 39)

Unpack and check the drive.

Grounding system compatibility
check (page 63)

If the drive will be connected to an IT (ungrounded)
system, make sure that the internal EMC filter is not
connected.

Installing the drive (page 40)

Install the drive mechanically.

Routing the cables (page 53)

Route the cables.

Connecting the power
cables (page 68)

Connect the power cables.

Connecting the control
cables (page 71)

Connect the control cables.

Installation checklist (page 81)

Examine the installation.

Refer to

ACS180 Quick installation

and start-up guide
(3AXD50000510344 [English])

, and

ACS180 Firmware manual
(3AXD50000467860 [English])

Commission the drive.

22 Introduction to the manual

Содержание ACS180-04S-03A7-1
































































































































































































Результаты поиска

Содержание ACS180-04S-03A7-1

Отзывы:

ABB ACS180-04S-03A7-1, Руководство по оборудованию, Страница: 22 / 192

Результаты поиска

Содержание ACS180-04S-03A7-1

Отзывы: