ABB ACS 800 Series Скачать руководство пользователя страница 55

Страница: 55 / 162

Mechanical installation of non-pre-assembled units (ACS800-04M)

Fastening the spacer

Fasten the the drive module to the cabinet or wall using a spacer at the top of the
module on the fastening side.

Fastening the top entry busbar and bottom exit shrouds (+B060)

Top entry busbar shroud

Fastening the spacer to the long side of the module
(flat mounting)

Fastening the spacer to the short side of the module
(bookshelf mounting)

Press the top cover on the
sides inwards to enable its tabs
to enter the slots in the shroud
when it is placed in position (4).

Remove the
protective film.

Step drill lead-throughs
for the busbars.

Fasten the shroud to the drive module

Содержание ACS 800 Series



































































































































































Результаты поиска

Содержание ACS 800 Series

Отзывы:

Похожие инструкции для ACS 800 Series

Бренды по названию

Популярные бренды

ABB ACS 800 Series, Инструкция по установке и эксплуатации шкафа

Результаты поиска

Содержание ACS 800 Series

Отзывы:

Похожие инструкции для ACS 800 Series

Бренды по названию

Популярные бренды