ABB ACQ810 Скачать руководство пользователя страница 20

Страница: 20 / 134

20 Introduction to the manual

Terms and abbreviations

Term/Abbreviation

Explanation

EMC

Electromagnetic Compatibility

EMI

Electromagnetic Interference

FIO-11

Optional analogue I/O extension

FIO-21

Optional analog and digital I/O extension

FIO-31

Optional digital I/O extension with four relays

FDNA-0x

Optional DeviceNet™ adapter

FENA-0x

Optional Ethernet/IP™ adapter

FLON-0x

Optional LonWorks® adapter

FSCA-0x

Optional Modbus adapter

FPBA-0x

Optional PROFIBUS DP adapter

Frame (size)

Size of the drive module. The drive modules described in this manual are of frame
size G.

IGBT

Insulated Gate Bipolar Transistor; a voltage-controlled semiconductor type widely
used in inverters due to their easy controllability and high switching frequency.

I/O

Input/Output

JCU

The control unit of the drive module. The external I/O control signals are
connected to the JCU, or optional I/O extensions mounted on it.

JINT

Main circuit board

JMU-xx

The memory unit attached to the control unit of the drive

RFI

Radio-frequency interference

Содержание ACQ810







































































































































Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды

ABB ACQ810, Руководство по оборудованию

Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды