ABB ACQ810 Скачать руководство пользователя страница 126

Страница: 126 / 376

126 Parameters

05.35

kWh December

Energy consumed during last December.

1 = 1 kWh

05.36

First in order

The first pump in the current Autochange sequence.

1 = 1

05.37

Time autochg

Time elapsed since last Autochange.

1 = 1 ms

05.39

Next start node

(Only valid when the drive is master.) Node number of the
next drive to be started.

1 = 1

06 Drive status

Drive status words.

06.01

Status word1

Status word 1 of the drive.

No.

Name/Value

Description

FbEq

Bit

Name

Information

Ready

1 = Drive is ready to receive start command.
0 = Drive is not ready.

Enabled

1 = External run enable signal is received.
0 = No external run enable signal is received.

Started

1 = Drive has received start command.
0 = Drive has not received start command.

Running

1 = Drive is modulating.
0 = Drive is not modulating.

Em off
(off2)

1 = Emergency OFF2 is active.
0 = Emergency OFF2 is inactive.

Em stop
(off3)

1 = Emergency OFF3 (ramp stop) is active.
0 = Emergency OFF3 is inactive.

Ack startinh 1 = Start inhibit is active.

0 = Start inhibit is inactive.

Alarm

1 = Alarm is active. See chapter

Fault tracing

0 = No alarm is active.

Ext2 act

1 = External control EXT2 is active.
0 = External control EXT1 is active.

Local fb

1 = Fieldbus local control is active.
0 = Fieldbus local control is inactive.

Fault

1 = Fault is active. See chapter

Fault tracing

0 = No fault is active.

Local panel 1 = Local control is active, ie. drive is controlled from PC tool or control

panel.
0 = Local control is inactive.

Fault(-1)

1 = No fault is active.
0 = Fault is active. See chapter

Fault tracing

13…15 Reserved

Содержание ACQ810
























































































































































































































































































































































































Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды

ABB ACQ810, Руководство по прошивке

Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды