ABB Ability MACHsense-R Скачать руководство пользователя страница 72

Страница: 72 / 74

Dimensions of DAU

The figure below shows the dimension drawing for mounting the DAU.

Certification

Regulatory: CE, FCC, IC

Loctite

AA 326

Loctite

AA 326 is a yellow to amber, no-mix, medium-viscosity (thixotropic)

structural and magnet bonder suitable for magnet bonding and resistant to
temperatures of up to +120 °C. It is activated with Loctite SF 7649.

Loctite

SF 7649

Loctite

SF 7649 is also known as Loctite 7649, used for surface preparation. It is

an activator that is solvent-based, with low temperature curing. It promotes the
curing speed of Loctite anaerobic adhesives and sealants without any significant
loss of joint strength.

WARNING!
Obey the safety instructions to use adhesive and cleaning products. Use all
personal safety equipment and keep the area well ventilated.

72 Technical data

Содержание Ability MACHsense-R










































































Результаты поиска

Содержание Ability MACHsense-R

Отзывы:

Похожие инструкции для Ability MACHsense-R

Бренды по названию

Популярные бренды

ABB Ability MACHsense-R, Руководство пользователя

Результаты поиска

Содержание Ability MACHsense-R

Отзывы:

Похожие инструкции для Ability MACHsense-R

Бренды по названию

Популярные бренды