ABB Ability MACHsense-R Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 74

ABB Ability MACHsense-R Скачать руководство пользователя страница 11

￭

General safety in operation

These instructions are for all personnel that work around the motor.

WARNING!
Obey these instructions. If you ignore them, injury or damage to the
equipment can occur.
Install emergency stop controls with restart lockouts. After an
emergency stop, a new start command can take effect only after you
reset the restart lockout.

•

Installing the DAU requires wiring, so do not try to install when a motor or
connected drive is energized. Do not work on the DAU while the drive, motor
cable, motor, control cables, or control circuits are energized.

•

Do not step on the motor.

•

Be careful, as the temperature of the motor’s outer casing will be high during
normal operation and especially after shut-down.

•

Observe the rotating parts of the motor and take care during installation.

•

Do not open the terminal boxes when they are energized.

Safety instructions 11

«
...
9
10
11
12
13
...
»

Содержание Ability MACHsense-R











































































Отзывы:

Нет отзывов