ABB A275-L59 Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 136

ABB A275-L59 Скачать руководство пользователя страница 122

Operation Manual / 4 Product description / A200-L

9 Taking a turbocharger out of operation / 9.2 Taking defective tur-
bochargers out of operation

© Copyright 2018 ABB. All rights reserved.

HZTL4036_EN

Revision N

November 2018

9.2.5

Engines without bypass around the turbocharger

To obtain a higher engine performance, the nozzle ring can be removed if required (see
chapter

Disassembly and assembly

).

Securing the cover ring

If the nozzle ring is removed for emergency operation, the clamping of the cover ring (57001)
to the gas outlet casing must be ensured. In this case, additional washers (01) must be
provided in accordance with the following table. These washers (01) are not supplied by ABB.

Fig. 63: Ensuring clamping of the cover ring

Product

h [mm]

d1 [mm]

d2 [mm]

A265-L

3.5 … 4.0

13

20

A270-L

3.5 … 4.0

13

20

A275-L

4.0 … 5.0

17

28

A280-L

4.0 … 5.0

21

34

Table 48: Required washers (01)

Part number

A265-L

A270-L

A275-L

A280-L

57005

M12

50 Nm

M12

50 Nm

M16

80 Nm

M20

160 Nm

Table 49: Tightening torque (57005)

1. Remove screws (57005).

2. Fit and tighten screws (57005) with high-temperature grease and washers (01) in accord-

ance with the table.

9.2.6

Blanking off the inlets and outlets

The chapter is only applicable for engines with several turbochargers and joint air and ex-
haust gas receivers. The cover plates for the compressor casing outlet, gas inlet and gas
outlet are not included in the ABB scope of delivery.
The following figure shows the positions where to fit the cover plates.

Page

94

/

108

«
...
120
121
122
123
124
...
»

Содержание A275-L59









































































































































Отзывы:

Нет отзывов