ABB A175-M66 Скачать руководство пользователя страница 107

Страница: 107 / 150

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.11 Installing the compressor casing

HZTL4033_EN

Rev.H

July 2021

3. Using screws (90196) and washers (90198), fasten lifting device (90190 / 90195) to com-

pressor casing (72000) and secure to crane.

4. Position the compressor casing (72000).

Tighten nuts (61037) crosswise.

5. Remove lifting device (90190 / 90195).

6. Tighten the three press-off nuts (61090) against compressor casing (72000) by applying

the corresponding tightening torque.

Installing diffuser

Fig. 61: Installing diffuser

Product

Size

Tightening torque [Nm]

A170-M

A175-M

Table 47: Tightening torque (77015)

1. Loop around diffuser (79000) with lifting gear and position it on the wall insert (77000).

2. Attach diffuser with screws (77015).

3. Grease the new O-ring (77040) and fit it.

Page

105

147

Содержание A175-M66





















































































































































Результаты поиска

Содержание A175-M66

Отзывы:

Похожие инструкции для A175-M66

Бренды по названию

Популярные бренды

ABB A175-M66, Руководство по эксплуатации

Результаты поиска

Содержание A175-M66

Отзывы:

Похожие инструкции для A175-M66

Бренды по названию

Популярные бренды