ABB 3HAC031670-001 Скачать руководство пользователя страница 20

Страница: 20 / 46

Illustration, PROFINET anybus device DSQC 688

xx0800000136

Network status LED

Module status LED

Link/Activity

LINK

RJ-45 connector

PROFINET IO

LEDs

This section describes the LEDs of the PROFINET anybus device.

Note

A test sequence is performed on the network status LED and on the module
status LED during start of the PROFINET anybus device.

Network status LED

Comments

Description

LED status

•

No power

•

No connection with a master

Offline

OFF

•

Connection with master established

•

Master in RUN state

Online (RUN)

Green

•

Connection with master established

•

Master in STOP state

Online (STOP)

Green, flashing

Module status LED

Comment

Description

LED status

Module not configured or no power.

Not initialized

OFF

Module is initialized.

Normal operation

GREEN

Diagnostic event(s) present.

Diagnostic event(s)

GREEN, 1 flash

Used by external configuration tools to identify
the node on the network.

Blink

GREEN, 2 flashes

Module in exception state.

Exception error

RED

Expected Identification differs from real identi-
fication.

Configuration error

RED, 1 flash

IP address not set.

IP address error

RED, 2 flashes

Device (Station) name not set.

Device name error

RED, 3 flashes

Module has encountered a major internal error.

Internal error

RED, 4 flashes

Continues on next page

Application manual - PROFINET Anybus Device

3HAC050968-001 Revision: C

2 Hardware overview

2.1 Main computer DSQC1000

Continued

Содержание 3HAC031670-001














































Результаты поиска

Содержание 3HAC031670-001

Отзывы:

Бренды по названию

Популярные бренды

ABB 3HAC031670-001, Руководство по применению

Результаты поиска

Содержание 3HAC031670-001

Отзывы:

Бренды по названию

Популярные бренды