ABACOM Technologies RF-LPS Скачать руководство пользователя страница 1

The RF-LPS is a low power RF controlled switch which draws only 90

µ

A!  Primarily intended as a remote 

controlled device for battery saving applications, the RF-LPS is designed to remotely connect and dis-
connect the (battery) power supply to a connected device.  The RF-LPS is used in conjunction with the 
2CH-REML two channel RF remote transmitter.  Pressing the GREEN  button on the remote will cause 
the RF-LPS to pass the external (battery) power supply of the connected device, turning it ON.  Pressing 
the RED button interrupts the external (battery) power to the connected device, turning it OFF.  The RF-
LPS is constantly powered by two internal Lithium-Ion batteries lasting up to sixteen months. The RF-
LPS is ideal as a power saving (retrofit) interface for applications that are usually constantly powered, but 
are not being used for continuous duty.   

Features 

 

Low current consumption (typically 90

µ

A) 

Long battery life: continuous operation up to 
16 months off internal batteries 

Switches any supply from 5V

dc

 to 35V

dc

 

Can switch external loads up to 400mA 

For higher currents, a relay may be used to 
switch the power supply 

Simple series connection between load 
power supply and load device 

Works in conjunction with the 2CH-REML 
handheld RF remote radio transmitter 

Operates on 433.92MHz 

Receiver has -94dBm sensitivity 

Open Field Range of up to 400 feet 

8 bit selectable address 

Typical Applications 
 

Low power remote switch 

Switch devices ON/OFF in areas which are 
difficult to reach 

Conserve battery power in remote locations 

*90

µ

A*  Low Power RF Controlled Switch 

RF-LPS 

External Device

Supply

Without the RF-LPS, the remote device is constantly on, drawing maximum current

With the RF-LPS, the supply is switched to the load via RF remote control. 

When OFF, the  supply drain is only 90 microamps ! 

External Device/Load

Load Supply O/P

RF-LPS

Supply

OFF

ON

ABACOM Technologies, Inc. 

 383 Bering Ave • Etobicoke • ON • M8Z 3B1 • Tel +1(416)236-3858 • Fax +1(416)236-8866 

www.abacom-tech.com 

80mm 

40mm 

Height: 20mm 

Содержание RF-LPS

Страница 1: ...Long battery life continuous operation up to 16 months off internal batteries Switches any supply from 5Vdc to 35Vdc Can switch external loads up to 400mA For higher currents a relay may be used to switch the power supply Simple series connection between load power supply and load device Works in conjunction with the 2CH REML handheld RF remote radio transmitter Operates on 433 92MHz Receiver has ...

Страница 2: ...em out of their holder Slide the new batteries in with the negative towards the cir cuit board Feed the antenna back through the hole in the enclosure insert the circuit board re place the bottom enclosure cover and insert the screws be careful not to over tighten screws Setting the Communication Address The RF LPS will only respond to valid transmissions matching its configured address The trans ...

Страница 3: ...s 1 8 are for configuring the system address These settings may be any combination provided they are the same settings for both the transmitter and the receiver Switch position 9 must always be set to OFF default position This is important for correct operation Switch 10 position will affect the output state of D3 pin header on the RF LPS DIP switch 10 in the OFF position default position will alw...

Страница 4: ...X BUTTON 1 TX BUTTON 2 VT D1 D2 D3 RF LPS O P ON ON ON OFF 1 0 0 1 or 0 OFF OFF ON 1 1 0 1 or 0 ON ON OFF ON OFF 1 0 0 1 or 0 OFF OFF ON 1 1 1 1 or 0 ON OFF default ON default ON OFF 1 0 1 1 or 0 OFF OFF ON 1 1 0 1 or 0 ON OFF OFF ON OFF 1 0 1 1 or 0 OFF OFF ON 1 1 1 1 or 0 ON From the above table the following can be noted VT always goes high upon a button press and may be used to indicate a vali...

Отзывы: