abaco systems SBC329 3U VPX Скачать руководство пользователя страница 99

Страница: 99 / 137

Publication No. SBC329-HRM/1

FPGA Registers 99

6.35 COM Port Enable Register (0x6BB)

Software should enable transceivers

after

setting the desired COM port mode (i.e.

RS232/RS422). Setting either of bits 0 or 1 to a ‘1’ will enable both COM1 a

nd COM2

transceivers. To disable transceivers, both of bits 0 and 1 must be cleared to ‘0’.

Bits

Read/Write Description

Default

7 to 2

Read only

COM8 to COM3 enable:
COM8 to COM3 are not available

000000

Read/Write

COM2 enable:

1 = COM transceivers enabled
0 = COM transceivers disabled

Read/Write

COM1 enable:

1 = COM transceivers enabled
0 = COM transceivers disabled

6.36 COM Port Mode Register (0x6BC)

Bits

Read/Write Description

Default

7 to 2

Read only

COM8 to COM3 mode:
COM8 to COM3 are not available

000000

Read/Write

COM2 mode:
1 = COM2 transceiver in RS422 mode
0 = COM2 transceiver in RS232 mode

Read/Write

COM1 mode:

1 = COM1 transceiver in RS422 mode
0 = COM1 transceiver in RS232 mode

Содержание SBC329 3U VPX










































































































































Результаты поиска

Содержание SBC329 3U VPX

Отзывы:

Бренды по названию

Популярные бренды

abaco systems SBC329 3U VPX, Справочник по аппаратуре

Результаты поиска

Содержание SBC329 3U VPX

Отзывы:

Бренды по названию

Популярные бренды