manualshive.com logo in svg

abaco systems SBC329 3U VPX, Справочник по аппаратуре

Поделиться
Скачать
abaco systems SBC329 3U VPX Скачать руководство пользователя страница 102

 

102  SBC329 3U VPX Single Board Computer 

  

Publication No. SBC329-HRM/1 

6.42  Scratchpad Register (0x6C6) 

This generic read/write register is available to software to validate FPGA access. 
It returns 0xFF by default. 

6.43  Test Register (0x6C7) 

Bits 

Description 

Default 

7 to 1 

Reserved 

0000000

b

 

0 

CPU daisy-chain status: 

1 = Chain fault 
0 = Chain OK 

N/A 

6.44  XMC Status Register (0x6C8) 

The SBC329 does not support PMC. 

Bits 

Description 

Default 

7 

XMC1 presence: 
1 = XMC1 is fitted 
0 = XMC1 is not fitted 

N/A 

6 

XMC1 VPWR voltage: 

Only 5V VPWR is supported 
0 = XMC1 VPWR rail is 5V 

0 

5 

XMC1 BIST status: 

1 = XMC1 BIST is active 
0 = XMC1 BIST is not active 

N/A 

4 to 0 

Reserved 

00100

b

 

6.45  Backplane Status Register (0x6CA) 

This register inverts the GA bits so that software can read a true slot number, e.g. the 
SBC329 in slot 1 (only GA0 pulled low) results in bits 4 to 0 reading 00001

b

. 

Bits 

Description 

Default 

7 

SYSCON status: 
1 = SBC329 is fitted into a System Controller slot (SYSCON backplane pin is low) 
0 = SBC329 is not fitted into a system controller slot (SYSCON backplane pin not pulled low) 

N/A 

6 

NVMRO status: 

1 = Backplane NVMRO signal is asserted 
0 = Backplane NVMRO signal is negated 

N/A 

5 

VPX GAP pin status: 

1 = GAP pin is high 
0 = GAP pin is low 

N/A 

4 to 0 

VPX GA4 to GA0 status (inverted) 

N/A 

Содержание SBC329 3U VPX










































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды