abaco systems PPC11A Скачать руководство пользователя страница 98

Страница: 98 / 159

98 PPC11A 6U VME Single Board Computer

Publication No. PPC11A-HRM/1

5.31

XMC/PMC Site 2 Status Register (Offset 0x6C9)

Bit Description

Default

XMC2 presence:

1 = XMC2 is fitted

0 = XMC2 is not fitted

XMC2 VPWR voltage. The XMC VPWR rail is always 5V on PPC11A.

0 = XMC2 VPWR rail is 5V

XMC2 BIST status:

1 = XMC2 BIST is active

0 = XMC2 BIST is not active

XMC2 reset out (MRSTO) status:

1 = XMC2 reset out is active

0 = XMC2 reset out is not active

In the default state, MRSTO always causes the PPC11A to reset.

This behavior can be disabled in the

Reset Control Register

Reserved

PMC2 enumeration ready status:
1 = PMC2 ERDY pin is active (OK to enumerate)

0 = PMC2 ERDY pin is not active

PMC2 VIO voltage:

1 = PMC2 VIO voltage is 5V

0 = PMC2 VIO voltage is 3.3V

The PMC VIO voltage is configured using a bit in the

EEPROM DIP switch

PMC2 presence:

1 = PMC2 is fitted

0 = PMC2 is not fitted

5.32

Backplane Status Register (Offset 0x6CA)

Bits

Description

Default

SYSCON status:

1 = PPC11A is fitted in the System Controller slot

0 = PPC11A is not fitted in the System Controller slot

N/A

Reserved

VME GAP pin status.
This bit reads the state of the VME GA parity pin. It is

not

inverted

N/A

4 to 0

VME GA4:0 status:

1 = GA pin pulled low

0 = GA pin not pulled low

The GA bits are inverted here so that the host software can read a true slot number

N/A

Содержание PPC11A
































































































































































Результаты поиска

Содержание PPC11A

Отзывы:

Похожие инструкции для PPC11A

Бренды по названию

Популярные бренды

abaco systems PPC11A, Справочник по аппаратуре

Результаты поиска

Содержание PPC11A

Отзывы:

Похожие инструкции для PPC11A

Бренды по названию

Популярные бренды