manualshive.com logo in svg

AB Quality ALLEN-BRADLEY 1791, Руководство пользователя

Поделиться
Скачать
AB Quality ALLEN-BRADLEY 1791 Скачать руководство пользователя страница 51

Chapter

6

6-1

Programming Your Analog Block I/O Module

In this chapter, we describe

  block transfer programming
  sample programs in the PLC-3 and PLC-5 processors
  module scan time issues

Your module communicates with the processor through bidirectional block
transfers. This is the sequential operation of both read and write block
transfer instructions.

For the analog block I/O modules, block transfer writes (BTWs) can
perform two different functions.

If you want to:

Description

This type of BTW is called:

configure the module

This involves setting the bits which enable the

programmable features of the module, such as

scaling, alarming, real time sampling, etc.

the 

configuration BTW"

send data to the output channels

of those modules having outputs

This type of BTW is generally shorter in length

than the configuring BTW because it does not

configure the module each time it is initiated.

the 

output update BTW"

The following example programs are minimum programs; all rungs and
conditioning must be included in your application program. You can
disable BTRs, or add interlocks to prevent writes if desired. Do not
eliminate any storage bits or interlocks included in the sample programs. If
interlocks are removed, the program may not work properly.

Your analog module works with a default configuration upon powerup as
long as a block transfer write (BTW) has not been initiated. The default
mode is binary scaling and the input range is +/–10V. In the default mode,
the alarms are off and the outputs are reset at 0.

Your program should monitor status bits (such as power up status, bad
configuration, output out of range, alarms, etc.) and block transfer read
activity.

The following example programs illustrate the minimum programming
required for communication to take place.

Chapter Objectives

Block Transfer

Programming

Содержание ALLEN-BRADLEY 1791

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды