Aastra OpenCom 100 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 244

background image

Installation

Installing the Memory Card

61

3.13

Installing the Memory Card

To operate the OpenAttendant and OpenVoice programme packages you require
a memory card (Compact Flash card Type I or Type II). The memory card contains
the following files:

■

the voice files and welcome/closing texts for the voicemail system

OpenVoice

as well as messages which callers have left,

■

the audio files for the programme package

OpenAttendant

, with which you

can create individual information systems such as voice portals and voicemail
systems.

Only use high speed memory cards which are recommended by Aastra. Other
memory cards or “Microdrive” type memory cards may not be able to maintain the
required access speed.

Note:

If you use a memory card other than one recom-

mended by Aastra, Aastra will not accept any responsibility
for the correct functioning of the

OpenVoice

and

OpenAt-

tendant

programme packages.

For further information, please contact your local dealer or the Aastra sales
department.

The following instructions are intended for persons authorised to install such
memory cards, in the event that there is still no memory card available in the com-
munications system.

3.13.1 Safety Precautions

Please note:

The memory card may only be installed by authorised per-
sonnel because the slot for the card is located on the mod-
ule board of the communications system.

DANGER!

High voltage inside the device.

«
...
61
62
63
64
65
...
»

Содержание OpenCom 100





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OpenCom 100

Бренд: Carel Страницы: 2

Бренд: elsner elektronik Страницы: 148

Бренд: Digitrax Страницы: 8

Бренд: Gemini Страницы: 7

Бренд: Tarfire Страницы: 31

Бренд: Kaye Страницы: 168

Бренд: Iluv Страницы: 40

Бренд: Duro Dyne Страницы: 16

Бренд: Hitachi Страницы: 242

SAAK66 - MINI HES W/CD PLAYER

Бренд: Panasonic Страницы: 14

SoundStation 2W

Бренд: Polycom Страницы: 46

SIMATIC S5 CPU Direct Driver

Бренд: Siemens Страницы: 16

SIMATIC PCS 7 FOUNDATION Fieldbus

Бренд: Siemens Страницы: 72

SIMATIC PCS 7 BOX

Бренд: Siemens Страницы: 130

XM-ZR704 Marketing

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды