background image

Installation,  Operation  and  Parts  Manual 

IMPORTANT SAFETY INSTRUCTIONS 

1.1 Important notices 

EverLift will offer one-year's quality warranty for the whole machine

during which any quality problem will be properly solved to 

the user's satisfaction. However, we will not take any responsibility for  whatever bad consequence resulted from improper installation 

and operation, overload running or unqualified ground condition. 

This model is specially designed for lifting motor vehicles that weighs within its outmost lifting capacity. Users are not allowed to use it 

for any other purposes. Otherwise, we, as well as our sales agency, will not bear any responsibility for accidents or damages of the 

hoist

Make sure to pay careful attention to the label of the lifting capacity attached on the 

hoist

 and never try to 

hoist

 cars with its weight 

beyond. 

Read this manual carefully before operating the machine so as to avoid economic loss or personnel casualty incurred by wrong operation. 

Without our professional advice, users are not permitted to make any modification to the control unit or whatever mechanical unit.     

1.2 Qualified personnel 

1.2.1 Only these qualified staff, who have been properly trained, can operate the 

hoist

1.2.2 Electrical connection must be done by a competent electrician.     

1.2.3 People who are not concerned are not allowed in the lifting area.   

1.3 Danger notices 

1.3.1 Do not install the 

hoist

 on any asphalt surface. 

1.3.2 Read and understand all safety warnings before operating the 

hoist

1.3.3 Do not leave the controls while the 

hoist

 is still in motion. 

1.3.4 Keep hands and feet away from any moving parts. Keep feet clear of the 

hoist

 when lowering. 

1.3.5 Only these properly trained personnel can operate the 

hoist

.  

1.3.6 Do not wear unfit clothes such as large clothes with flounces, tires, etc, which could be caught by moving parts of the 

hoist

1.3.7 To prevent evitable incidents, surrounding areas of the 

hoist

 must be tidy and with nothing unconcerned.  

1.3.8 The 

hoist

 is simply designed to 

hoist

 the entire body of vehicles, with its maximum weight within the lifting capacity. 

Model 

(mm) 

(mm) 

(mm) 

(T) 

(T) 

(T) 

(T) 

FL-8801 

1900 

2000 

110 

1.8 

1.2 

1.2 

1.8 

AL-

3000AG (FL-8801)

Содержание AutoLift AL-3000AG






































Отзывы: