manualshive.com logo in svg

AAON RN Series, Установка, эксплуатация и обслуживание, Страница: 66 / 136

Поделиться
Скачать
AAON RN Series Скачать руководство пользователя страница 66

 

66 

(NaHCO) before the last rinse ensures that all 
acid is neutralized.   
 

E-Coated Coil Cleaning 

Documented  routine  cleaning  of  e-coated 

coils  is  required  to  maintain  coating 
warranty  coverage  for  fin  and  tube  and 
microchannel 

coils. 

See  the 

AAON 

E-Coated Coil  Maintenance Record sheet.  

 

 

 
Surface  loaded  fibers  or  dirt  must  be 

removed  prior  to  water  rinse  to  prevent 
restriction  of airflow.  If unable  to back wash 
the  side  of  the  coil  opposite  of  the  coils 
entering  air  side,  then surface loaded  fibers 
or  dirt  must  be  removed  with  a  vacuum 
cleaner. If a vacuum cleaner is not available, 
a 

soft  non-metallic

  bristle  brush  may  be 

used. In either case, the tool  must be applied 
in the direction  of the fins. Coil  surfaces can 
be  easily  damaged  (fin  edges  bent  over)  if 
the tool  is applied  across the fins.  

  
Use of a water stream, such as a garden hose, 

against  a surface loaded  coil  will  drive  the 
fibers  and dirt  into  the coil.  This  will  make 
cleaning  efforts  more  difficult.  Surface 
loaded  fibers  must  be  completely  removed 
prior  to using low velocity  clean water rinse.  

  
A 

monthly

 

clean 

water 

rinse 

is 

recommended  for  coils  that  are applied  in 
coastal or industrial  environments  to help  to 
remove chlorides,  dirt,  and debris. It is very 
important 

when 

rinsing, 

that 

water 

temperature is  less than 130°F  and  pressure 
is  less than 100  psig  to avoid  damaging  the 
fin  edges.  An  elevated  water  temperature 
(not  to  exceed  130°F)  will  reduce  surface 

tension,  increasing  the  ability  to  remove 
chlorides  and dirt.   

  

 

 

Quarterly cleaning is essential to extend the 

life  of  an e-coated coil  and is  required to 
maintain coating warranty coverage.

  

Coil  cleaning  shall  be  part  of  the  unit’s 
regularly  scheduled maintenance  procedures. 
Failure  to clean an

 

e-coated coil  will  void  the 

warranty  and  may  result  in  reduced 
efficiency  and durability. 
 

 

 
For routine  quarterly  cleaning,  first clean the 

coil  with  the  below  approved  coil  cleaner. 
After  cleaning  the  coils  with  the  approved 
cleaning  agent,  use  the  approved  chloride 
remover  to  remove  soluble  salts  and 
revitalize  the unit.   

 

 

 

 

 

Electric  shock  hazard.  Shut  off  all 
electrical  power  to  the  unit  to  avoid 
shock  hazard  or  injury  from  rotating 
parts.

 

    

 

WARNING

 

 

 

 

High  velocity  water  from  a  pressure 
washer  or  compressed  air  must  only 
be  used  at  a  very  low  pressure  to 
prevent  fin  and/or  coil  damages.  The 
force of  the  water or air  jet  may bend 
the  fin  edges  and  increase  airside 
pressure 

drop. 

Reduced 

unit 

performance 

or 

nuisance 

unit 

shutdowns may occur. 

  

 

CAUTION 

 

 

 

 

Harsh  chemicals,  household  bleach, 
or  acid  cleaners  must not  be  used  to 
clean outdoor or indoor e-coated coils. 
These cleaners can be very difficult  to 
rinse out of the coil and can accelerate 
corrosion  and  attack  the  e-coating.  If 
there  is  dirt  below  the  surface  of  the 
coil,  use  the  recommended  coil 
cleaners. 

  

 

CAUTION 

 

Содержание RN Series









































































































































Отзывы:

Нет отзывов