manualshive.com logo in svg

AAON PREHEAT-X, Техническое руководство

Поделиться
Скачать
AAON PREHEAT-X Скачать руководство пользователя страница 5

5

PREHEAT-X Technical Guide

Overview

The PREHEAT-X is designed to control fixed stages of Preheat 

and optional modulating Preheat to maintain a desired Preheat 

Leaving Air Temperature Setpoint. See 

Figure 1

, 

this page

 for 

dimensions. See 

Figure 2 and 3, pages 7 and 8

 for wiring details.

Features

The PREHEAT-X has the following features:

• 

Can be operated as a stand-alone module or comm-

unicating  with  the  VCCX2  or  other AAON  unit 

controllers.

• 

Monitors the Preheater Leaving Air Temperature and 

Leaving Air Reset Signal and controls to maintain the 

setpoint

• 

Contains a 2 x 8 LCD character display and four buttons 

that allow for status display and setpoint changes

Figure 1:  PREHEAT-X Dimensions

5.73

5.24

2.62

5.63

5.04

0.21

2.04

0.57

4.09

Note:

Depth is 1.50 inches.

Note:

All dimensions are in inches.

OVERVIEW

General Information

NOTE: 

The  PREHEAT-X  contains  no  user-serviceable 

parts. Contact qualified technical personnel if your 

PREHEAT-X is not operating correctly.

Содержание PREHEAT-X





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды