AAON PREHEAT-X Скачать руководство пользователя страница 21

Страница: 21 / 28

PREHEAT-X Technical Guide

General

The PREHEAT-X is equipped with LEDs that can be used to

verify operation and perform troubleshooting. See

Figure 6,

this page

for the LED locations. The LEDs associated with these

inputs and outputs allow you to see what is active without using

a voltmeter. The LEDs and their uses are as follows:

STATUS LEDs

POWER -

This green LED will light up to indicate that 24 VAC

power has been applied to the controller.

Diagnostic LEDs

ALARM -

This red LED located on the PREHEAT-X’s cover

above the LCD display will light up to indicate an alarm. The

type of alarm(s) will be shown on the LCD display.

Communication LED

COMM -

This yellow LED will light up and blink when

communications are detected.

Relay LEDs

RLY 1-6 -

These green LEDs will light up and stay lit as long as

the Heat Relay(s) is active.

Binary Input LEDs

HEAT EN -

This green LED will light up when Heat is enabled.

EMERGENCY SHUTDOWN -

This green LED will light up when

Emergency Shutdown input has 24 VAC applied to it.

ALARM LED

STAT LED

OS LED

APP LED

HEAT ENABLE LED

EMERGENCY

SHUTDOWN LED

COMM LED

WDOG LED

ALARM LED

Figure 6: PREHEAT-X LED Locations and Descriptions

TROUBLESHOOTING

LED Diagnostics

Содержание PREHEAT-X





























Результаты поиска

Содержание PREHEAT-X

Отзывы:

Бренды по названию

Популярные бренды

AAON PREHEAT-X, Техническое руководство

Результаты поиска

Содержание PREHEAT-X

Отзывы:

Бренды по названию

Популярные бренды