manualshive.com logo in svg

AAON PREHEAT-X, Техническое руководство

Поделиться
Скачать
AAON PREHEAT-X Скачать руководство пользователя страница 15

15

PREHEAT-X Technical Guide

Status Screens

Refer to the following map when navigating through the Status 

Screens. From the STATUS Screen, press 

<ENTER>

 to scroll 

through the screens.

STATUS 

Status Screens shown below automatically if LCD display is left on 

the screen for 20 seconds.

SOFTWARE
VER X.XX 

CURRENT SOFTWARE VERSION

Displays the current software version installed in the module.

PREHEAT

ENABLED 

PREHEAT 

Gives the Enabled status for the Preheat Mode. The PREHEAT-X 

can be enabled from one of the following: (1) Binary Input in Stand-

Alone Mode, (2) E-BUS command from VCCX2 or other AAON unit  

controllers, or (3) BACnet point.

CONT TMP

XX.X 

CONTROL TEMPERATURE

Displays the current controlling temperature. This could be one of 

the following based on configuration: (1) Leaving Air Sensor 1, 

(2) Leaving Air Sensor 2, or (3) the average of both.

.

LA SPT

XX.X 

LEAVING AIR TEMPERATURE SETPOINT

Displays the current Leaving Air Setpoint the module is trying to 

maintain. This value can come from the following based on 

configuration: (1) Internal Set/- Setpoint Reset Input, 

 

(2) E-BUS Input from VCCX2 or other AAON unit controllers or  

(3) BACnet point.

.

STGS ON

2 

CURRENT NUMBER OF ACTIVE STAGES

Displays the number of heat stages currently energized.  

This includes the First Modulating Stage of Heat.

.

MOD HEAT

XX% 

MODULATING HEATING OUTPUT

Displays the current Modulation Output Percentage of both the  

Analog and PWM outputs (they control together).

LA1 TEMP

XX.X 

LEAVING AIR TEMPERATURE 1 

Displays the Leaving Air Temperature 1 Sensor’s current reading.

LA2 TEMP

XX.X 

LEAVING AIR TEMPERATURE 2 

Displays the Leaving Air Temperature 2 Sensor’s current reading.

AVG TEMP

XX.X 

AVERAGE TEMPERATURE

Displays the current average temperature of both 

Leaving Air Temperature Sensors.

LCD SCREENS

Status Screens

Содержание PREHEAT-X





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды