AAON LZ Series страница 77 Скачать руководство пользователя | Manualshive

Страница: 77 / 104

background image

77

Pump Piping - General

The  discharge  valve  only  is  to  be  used  to
throttle  pump  flow,  not  the  suction  valve.
Care must be taken in the suction line layout
and  installation,  as  it  is  usually  the  major
source  of  concern  in  centrifugal  pump
applications

Alignment

Alignment is unnecessary on close-coupled
pumps as there is no shaft coupling.

Split-coupled units are accurately aligned at
the factory prior to being shipped and do not
need re-aligning when installed.

Pump Operation

Starting Pump

Ensure that the pump turns freely by hand, or
with  some  mechanical  help  such  as  a  strap
and  lever  on  larger  pumps.  Ensure  that  all
protective  guarding  is  securely  fixed  in
position.

The pump must be fully primed on start up.
Fill the pump casing with liquid and rotate the
shaft by hand to remove any air trapped in the

impeller.  On  split  coupled  units,  any  air
trapped  in  the  casing  as  the  system  is  filled
must  be  removed  by  the  manual  air  vent  in
the  seal  flush  line.  Close-coupled  units  are
fitted  with  seal  flush/vent  lines  piped  to  the
pump suction area. When these units operate
residual air is drawn out of the pump towards
the suction piping.

“Bump” or energize the motor momentarily
and check that the rotation corresponds with
the directional arrow on the pump casing. To
reverse  rotation  of  a  three  phase  motor,
interchange any two power leads.

Start  the  pump  with  the  discharge  valve
closed and the suction valve open,  and then
gradually open the discharge valve when the
motor  is  at  operating  speed.  The  discharge
valve  may  be  cracked”  or  open  slightly  at
start up to help eliminate trapped air.

When  stopping  the  pump:  Close  the
discharge valve and de-energize the motor.

DO  NOT  run  the  pump  against  a  closed
discharge  valve  for  an  extended  period  of
time. (A few minutes maximum)

Star-Delta  motor  starters  should  be  fitted
with  electronic/mechanical  interlocks  that
have  a  timed  period  of  no  more  than  40
milliseconds  before  switching  from  star
(Starting) to delta (Run) connection yet allow
the  motor  to  reach  full  star  (Starting)  speed
before switching to delta (Run).

Should the pump be noisy or vibrate on start-
up  a  common  reason  is  overstated  system
head.  Check  this  by  calculating  the  pump
operating  head  by  deducting  the  suction
pressure  gauge  value  from  the  discharge
gauge  reading.  Convert  the  result  into  the
units of the pump head as stated on the pump
nameplate  and  compare  the  values.  Should
the  actual  pump  operating  head  be

Use Caution. Piping may carry high
temperature fluid.

CAUTION

Discharge valve only is to be used to
throttle pump flow.

CAUTION

Do not run pumps with discharge
valve closed or under very low flow
conditions.

CAUTION

«
...
75
76
77
78
79
...
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ Series

MILLENNIUM YCAS0230

Бренд: York Страницы: 168

Бренд: Daikin McQuay Страницы: 84

Бренд: MTD Страницы: 16

Бренд: MTD Страницы: 24

MAXIMULCH FIXED 3 Series

Бренд: Agrisem Страницы: 49

Disc-O-Mulch GOLD PORTE

Бренд: Agrisem Страницы: 50

Бренд: P.Lindberg Страницы: 94

Cutler-Hammer AMPGARD

Бренд: Eaton Страницы: 28

Бренд: Qualcast Страницы: 20

Бренд: Raider Страницы: 130

ICE CHILLER TSC-C-D

Бренд: Baltimore Aircoil Company Страницы: 30

Бренд: Jensen Страницы: 132

Бренд: Parkside Страницы: 110

Бренд: Daikin Страницы: 60

Бренд: Brillion Страницы: 64

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 56

Бренд: Land Pride Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды